Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
Have you been trying to locate ideas concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is readily obtainable, the job can move speedily; if you have to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need an assistant to vacate the old tub and embeded in the brand-new one. See to it you have actually qualified yourself for the work as well as are comfortable trying it. Rather than employing a specialist to take over a halfway-completed job, it is far better to think about utilizing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This post will assist you set up a new bathtub in your restroom if you have currently acquired a brand-new tub as well as don't require to transform the setup of your previous water pipelines.
Your tools as well as material checklist need to make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous kind ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wooden boards under its feet, place the tub in the needed placement. The wood boards are helpful in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bath tub till the level reviews level.
To install taps, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system and also examine all joints and also new pipework for leaks and tighten them if required. Fill the bathtub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of a minimum of once as this will settle it into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and also the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our topic on How to Install a Bathtub Yourself. Thank you for taking the time to read our article post. Enjoyed reading our entry? Please share it. Help another person discover it. Thank you for your time. Don't hesitate to visit our website back soon.
Instant Quote
Report this page